- All
Reset
Pull M out. Hold A,B and C down simultaneously for
3 seconds then release them. All digital segments
will be highlighted.
Press and release B, digital display will show zero's
and upper display will show "F_H" (function
hand)
Use A to align function hand to "60"
Press and release B, upper digital display will show
"HR" (hours)
Hold A down to align regular hour and minute hands
to 12 o'clock position and 24 hour hand to 2400 hours.
All three hands will move simultaneously.
Press and release B, upper digital display will show
"SEC" (seconds).
Hold A down to align second hand to 12 o'clock position.
Press M to finalize zero positioning. Watch will beep,
confirming all reset and zero positioning.
|
- Using
Race Timers 1 & 2
Race Timer 1 (R-1) has an auto-repeat function and
will repeat a countdown from a set time, automatically
for 3 times the stop.
Race Timer 2 (R-2) has an auto-chronograph function
and will automatically switch to a stopwatch mode,
registering accumulated time after finishing the countdown.
Setting procedure is the same for both R-1 and R-2
timers can be set from 60 minutes down to 10 minutes
in 5 minute increments and then ad 6,5,3 and 1 minute.
To set R-1 or R-2 timers, press mode button to move
to R-1 or R-2. Pull mode button out, minutes will
flash. Use C button to set minutes to desired time.
Push mode button in to finalize setting.
Push A button to start or stop countdown and C button
to reset to timer set time. If C button is pushed
during countdown, timer will "fly-back"
to set time and start the countdown again.
Timer sound signals are the same for R-1 and R-2.
During the countdown, there are sound signals every
minute, starting at 10 minutes down to 1 minute, for
each 10 seconds down to 10 and then every second from
5 to time up. At time up, sound signals for 5 seconds.
|
|
- Setting
the Time
Press and hold B button down for 3 seconds, hour
and minute hands will retract to the 12 o'clock position.
This will permit an unobstructed view of the digital
displays during setting procedures.
Press and release M button to move mode indicator
hand to "TME" (time) then set city code
to one representing your time zone.
Press and release A button to change city code eastward
and C button to move westward.
When city code has been selected, pull M button out.
Hour, minute and second figures will all flash.
Press and release C button to select daylight or standard
time (summer indicates daylight). The time will change
accordingly.
Press and release A button, seconds will blink. Reset
seconds by using C button.
Press and release A button, minutes will blink. Use
C button to advance minutes, For fast advance, hold
C button down.
Press and release A button, Hours will blink. Use
C button to advance hours. Note a.m. or p.m.
Press and release A button, 12H or 24H will blink.
Use C button to select a.m. / p.m. time (12H) or military
time (24H).
Press M button to finalize setting of digital time.
(Hour retractor is released and hour and minute hands
move to indicate UTC time.) All other cities are adjusted
automatically when one city is set to correct time,
including the UTC digital display time.
After you have set digital time and release the retractor,
if you want analog (hands) time to indicate the time
in your zone (city code), press buttons A and C simultaneously.
The digital time (your time zone) will be switched
to the analog display and vice versa. City code and
digital time can now be changed to your time zone
by using A button (eastward) or B button (westward).
Both analog and digital time now match.
If you want a time zone different than that shown
on the digital display, to be shown by the analog
(hands), move the digital time to the desired zone
and repeat the switching function.
|
|
- Setting
the Calendar
Using the M button, move the mode indicator hand
to CAL. Note city code. If needed, use A button to
move city code eastward and C button to move westward.
Pull M button out to setting position, month number
will flash. Correct month by using C button.
Press and release A button, date will flash. Correct
date by using C button
Press and release A button, day will flash. Use C
button to correct day.
Press and release A button, year will flash. Use C
button to correct year.
Press M button in to finalize calendar setting.
|
- Using
the Chronograph
Use M button to move mode indicator to CHR
Press and release A button to start or stop time measurement
While chronograph is running, press C button for split
time. Display now shows elapsed time for 10 seconds
while continuing to measure elapsed time internally.
After 10 seconds, display picks up counting at the
true elapsed time and continues running until C button
is pressed for split time again or A button is pressed
to stop.
After chronograph is stopped, press C button to reset
to zero.
|
- To
Set Alarms
Use the M button to move the mode indicator to
AL-1. Use A or C button to select the city code
Pull mode button out to setting position, display
blinks. Use C button to set alarm on or off.
Press and release A button, hours will blink. Correct
hours with C button.
Press and release A button, minutes will blink. Correct
minutes with C button.
Press M button in to finalize alarm setting.
Alarm 2 is set in the same way as Alarm 1. When alarms
sound, press any button to stop sounding.
|
|
