- To
Switch Modes
Press and release M button, modes will be changed
in the following sequence: Time/Calendar (or seconds),
Alarm, Chronograph, Dive Log and Dive Alarms
|
- To
Set Digital Time (Set Analog Time After digital
is set)
Depress B button for 3 seconds, seconds will flash.
Press and release A button, seconds will reset to
"00" and start counting upward again
Press B button and minutes will flash. Use A button
to advance minutes. (Hold button down for rapid advance)
Press B button, hours will flash. Use A button to
advance hours. If in 12 hour mode check for A or P
to indicate AM or PM.)
Press B button, month number will flash. Use A button
to advance month.
Press B button, date will flash. Use A button to advance
date.
Press B button, year will flash. Use A button to advance
year. Auto calendar is self correcting through the
year 2099. Press B button, 12H/24H will flash. Use
A button to select 12H for AM/PM time or 24H for military
time. Press B button to finalize digital time setting.
|
- Set
Analog Time
Unscrew lock down crown until it is free of the case.
Pull the crown out to that the second hand stops at
'0' position.
Turn crown clockwise and advance hands one minute
ahead of digital time. When digital seconds are at
'00', push crown in. Both seconds now match. Always
remember to press crown firmly and turn it clockwise
until it is screwed tightly against the case after
setting hands.
|
|
- To
Set Daily Alarm
Press M button to move display to alarm mode
Depress B button for 3 seconds; hours will blink and
ON/OFF display will show ON. Use A button to advance
hours. Pay particular attention to A (AM) or P (PM)
unless time is in military time (24H)
Press B button; minutes will flash. Press A button
to advance minutes. Press B button to finalize setting.
While in alarm mode, press A button to activate or
deactivate the alarm. (ON/OFF)
|
- To
Using the Chronograph
Press M button to move display to chronograph mode.
Upper display will show '0' hours and '00' minutes
(if in reset condition). The lower display will show
'00-' seconds and '--'1/100' second.
Press A button to start or stop counting. When counting
is stopped, press B button to reset display to zeros.
Button B may be used while chronograph is running
to display split time.
|
- To
Check Dive Log
Move display to dive log mode by pressing the M button.
First items displayed show the dive number (upper)
and month and date (lower) of the last dive for 3
seconds and then switches to maximum depth of the
last dive in the upper display and the elapsed time
(total time) of the last dive in the lower display.
Press A button; log display shows dive time (upper)
and dive finish time (lower).
Press A button; log display shows the average depth
of the last dive (upper) and the lowest water temperature
during the last dive (lower).
|
|
- To
Set Dive Alarms
Move display to dive alarm mode (D.A.L.) by pressing
the M button. The upper display now shows depth alarm
setting and lower display shows dive time alarm setting.
Depress B button for 3 seconds; depth figure begins
to flash and lower display changes to number of times
during the dive you want the depth alarm to sound.
Press A button to increase depth alarm setting in
3 foot increments. Hold A button down for rapid advance.
Press B button "the number of times you want
the depth alarm to sound during the dive" will
flash. As a button is pressed, figure will change
in the following sequence: OH, OFF, -1, -2, -3. -4
and -5. When a selection is made, press B button;
lower display changes back to dive time alarm figure
(flashing). Press A button to increase dive time in
5 minute increments to a maximum of 95 minutes. Press
B button to finalize dive alarm settings. Press M
button to return to time/calendar.
|
- Note
While in time/calendar mode, lower display can
be changed to display seconds or calendar by pressing
button A. Hold button A down for 3 seconds to switch
to temperature display. To switch back to seconds,
press A button.
|
|
