- All
Reset
After a battery change or in case of an abnormal display,
perform ALL RESET.
Press and release mode button to move mode indicator
to TME (time) mode. Pull crown out to setting position
and press and hold buttons A, B and M down simultaneously
for 3 seconds, then release them. All digital segments
in the displays will be highlighted (black).
Press crown in. At this point, a beep is heard indicating
that ALL RESET is complete. Set correct time and calendar
and other modes as needed.
|
- To
Set Analog Time
Pull crown out to hand setting position and turn crown.
|
- Switching
Digital Modes
Modes can be changed in the following sequence: TME
(time), CAL (calendar), AL-1 and AL-2 (alarms), CHR
(chronograph), TMR (timer), SET (zone setting) by
pushing and releasing the Mode (M) button.
|
- Setting
Digital Time
Use button B to move your time zone city code
into digital display 2.
If TME is not showing in digital mode display, use
Mode (M) button to select TME.
Press button B in and hold for 3 seconds to switch
to digital time setting mode. S.T. (Summer time) used
for daylight saving time and "ON" or "OF"
will begin flashing. Use button A to select S.T. "ON"
or "OF" (off).
Press and release button B, seconds figures will blink.
Use button A to reset seconds.
Press and release button B, minutes will blink. Use
button A to adjust minutes. Hold A in for rapid change.
Press and release button B, hours will blink. Use
button A to set hours according to a.m. or p.m.
Press button B, 12H will blink. Use button A to select
24H (military time) if desired.
Press button B or M to return to normal time display.
|
|
- To
Set Calendar
Press and release the mode button to move mode
indicator to CAL (calendar). Digital display I shows
month and date. Digital display II shows City code.
Hold button B in for three seconds and then release,
month number starts blinking. Press button A to advance
month number.
Press and release button B, date starts blinking.
Press button A to advance date.
Press and release button B, digital display I shows
the year and year numbers will be flashing. Press
button A to advance year.
After button B or M is pressed, digital display l
shows month number and date.
|
- To
Set Alarms
Using mode button, move the mode indicator to ALM
1 (or ALM 2). Press and hold button B for 3 seconds
then release it, the hours in digital display I will
blink. Press button A to advance hours.
Press and release button B, minutes in digital display
I will blink. Press button A to set minutes.
Setting alarm time sets alarm to on.
Press button B to finalize setting.
To switch alarm off or on while in alarm mode, press
button A. While in alarm mode, digital display II
shows city code.
|
|
- Using
the Chronograph
Use mode button to move to CHR mode. The chronograph
can measure up to 23 hour, 59 minutes, 59 and 99/100
seconds.
Press button A to start or stop chronograph. Digital
display I shows minutes, seconds and 1/100 seconds.
Digital display ll shows measured time hours.
If button B is pressed while chronograph is running,
a split time is displayed for 10 seconds as chronograph
continues counting elapsed time internally.
If button B is pressed when counting is stopped, chronograph
is reset to zero.
|
- Using
the Timer
Use mode button to move to TMR (Timer mode). Timer
can be set to countdown from 99 minutes down to 1
minute in 1 minute intervals. Digital display ll shows
Timer set time in minutes and digital display I shows
Timer minutes and seconds remaining.
Press button B to set Timer minutes
Press button A to start or stop Timer countdown.
Pressing button B after Timer is stopped resets it
to original Timer set time.
If button B is pressed while Timer is running, the
time is reset to the original Timer set time and restarts
the countdown automatically. When Timer counts down
to zero, the time up signal sounds for 5 seconds and
the display returns to the Timer set time and stops.
|
|
