Watchliquidators

Analog/Digital

Time setting
1. Press 3 to display time feature.
2. Press 2 to select the time display you wish to reset. Keep button depressed until seconds begin to blink (approx. 2 sec.)
3. While display is blinking, press A to adjust.
4. Press 2 to reset minute display.
5. Press 1 to adjust minutes while the display is blinking.
6. Repeat this process to set the hour, and military or standard time display (12/24 hour.)

Setting other functions
1. Press 3 to select the function you wish to adjust the alarm and date.
2. Press and hold 2 until function begins to blink.
3. While blinking, press 1 to make function adjustment.

Floating Ana-Digi

Setting Time/Date
Setting the analog hands
1. Press 3 to display time feature.
2. Press 2 to select the time display you wish to reset. Keep button depressed until seconds begin to blink (approx. 2 sec.)
3. While display is blinking, press 1 to adjust.
4. Press 2 to reset minute display.
5. Press 1 to adjust minutes while the display is blinking.
6. Repeat this process to set the hour, and military or standard time display (12/24 hour).

Setting digital time
1. Press and release the A button until the time shows in the digital display.
2. Press and hold A until the seconds begin to flash. Press 2 to reset the seconds.
3. Press 3 , the hours will begin to flash. Press 2 to set the hours. Repeat this process to set the minutes, year, month, date and day of the week. Press 1 to stop the digits from flashing. To change between 12 and 24 hr. time modes, press and hold the 3 button.

Setting the dual time
1. Press and release the 1 button until 'Dual' shows in the digital display.
2. Press and hold 1 until the hours begin to flash.
3. Press 2 to set the hour.
4. Press 3, the minutes will begin to flash.
5. Press 2 to set the minutes. Repeat this process to set the month, and date.
6. Press 1 to stop the digits from flashing.

Alarm/Timer
Setting the alarm
1. Press and release the 1 button until the Alarm time shows in the digital display.
2. Press and hold 1 until the hours begin to flash.
3. Press 2 to set the hour.
4. Press 3, the minutes will begin to flash.
5. Press 2 to set the minutes. Press 2 to stop the digits from flashing.
There are seven (7) different melodies that can be set for the alarm. To hear the selected melody, press 3. The selected melody will begin to play. To start a different melody press 3 again. To stop the melody, press any button. Push 2 to turn alarm on or off. Alarm is on if ALM is shown, off if it is not.

Big Tic

Time Setting
1. Pull crown out to position B.
2. Turn the crown until the desired time appears.
3. Push the crown back to position A .

Scrolling Big Tic

Time Setting
1. Pull crown out to position B.
2. Turn the crown until the desired time appears.
3. Push the crown back to position A. Press the pusher to alternate between seven different display choices.

Big Digital Date

To Light Up The Display
Press button 1.

To set the calendar
Press button 2 and hold for two seconds.
Entering into the setting mode, the first
element to be set will be flashing in the 6:00
display. First set the hour. The flashing digits
in the 6:00 display will indicate hour.
1. Press button 1 to advance. Holding button A will auto-advance the
digits quickly.
2. When correct digit is displayed, press 2.
Continue steps 1 and 2 above for the each setting in the following
sequence:
€ Hour setting‹HR
€ Minute setting‹MI
€ Second setting‹SE
€ Year setting‹YR
€ Month setting‹MO
€ Date setting‹DA
3. Press button 2 to exit the sequence.

Once the sequence is completed, the calendar function will set
automatically. The day of week is automatically calculated.

The setting mode will exit automatically if no key operation is done
for 60 seconds.

Multi-Big-Tic

Setting Time/Date
Time mode
1. Display shows "HOUR:MINUTE" and second dig its at bottom of display.
2. Press 3 to switch 12/24 Hour display format.
3. Digital time is not synchronized with the analog movement.

To set time
1. Press and hold 4 for 2 seconds.
2. Hour digit is blinking. Press 3 to advance to next digit. Press & hold 3 to advance quickly.
3. Press 1 to advance to next digit.
4. Press 4 to exit setting mode.
5. Watch will auto exit to Big Tic mode if pushers are not pushed in 2 minutes. Original setting values will remain.

To set seconds
Press 3 to reset the second digits to "00".

Alarm/Timer
Alarm mode
1. Display shows "HOUR:MINUTE".
2. Press 3 to turn Alarm On/Chime Off. Press 3 again to turn Alarm On/Chime On. Press 3 again to turn Alarm Off/Chime On. Press 3 again to turn Alarm Off/Chime Off. Alarm is on when is on display. Chime is on when is on display. When on, these icons stay on display in all modes.
Please Note - If Hourly Chime is On, key tone is on. If Hourly Chime is Off, key tone is off.

To set alarm
1. Press and hold 4 for 2 seconds until short beep tone.
2. Hour digit is blinking. Press 3 to advance. Press & hold 3 to advance quickly.
3. Press 1 to advance to next digit.
4. Press 4 to exit setting mode. You will hear one short beep tone.
5. When the alarm time is reached, the watch will stay in current mode. Alarm sound lasts for 20 seconds. Hourly Chime is 2 beeps. Press any key to stop alarm sound.
6. Auto exit to Big Tic mode if pushers are not pushed in 2 minutes. Original setting values will remain.

Countdown timer mode
1. Display shows "MINUTE:SECOND" and "HOUR" counter at bottom of display with.
2. Press 3 to start and pause timer.
3. When the countdown timer is counting, the blinks on display in all modes except mode titles.
4. When TIMER reaches "0:00" and "0" on bottom of display, alarm will sound for 20 seconds. After 20 seconds, alarm sound and counter stops and all digits freeze.
5. Press any key to stop alarm sound.
6. Press 3 to recall previous timer setting.
7. Press 3 again to restart timer.

To set countdown timer
1. Press and hold 4 for 2 seconds.
2. Hour digit is blinking. Press 3 to advance to next digit. Press & hold 3 to advance quickly.
3. The setting sequence is HOUR (0-19), Minute (0-59), and Second (00-59). Maximum setting is '19HR 59MIN: 59SEC'.
4. Press 4 to exit setting mode.

Digi-Multifunction

Setting Time/Date
Time Mode
1. Entering the Time Mode, "TME" will be shown for 3 seconds.
2. Time will then be displayed. Hour, minute will be shown in upper row. Second will be shown on lower row. Hour display will not have the leading zero for both 12 and 24 hour format.
3. Press 3 to switch between 12/24 hour display format.
4. Press and hold 2 for 2 seconds to enter into the Time Setting with double beep tone.

Time Setting Mode
1. Entering into the setting mode, hour will be flashing for setting.
2. Press 3 to advance the setting. If 3 is pressed and held for 2 seconds, auto advance function will then be activated.
3. Press 1 to cycle through the hour, minute and second setting.
4. Pressing 3 will reset the second to zero during the second setting.
5. If the setting is done, press 2 once to exit the setting. Time Mode will then be retrieved.

Date Mode
1. Entering the Date Mode, "CAL" will be shown for 3 seconds.
2. Month, day and day of week will then be shown. Month, day (or day, month) will be shown on upper row. Day of the week will be shown at bottom.
3. Press 3 to switch between the month/day display.
4. Press 1 to change into Alarm Mode.
5. Press 4 to turn on the EL for 3 seconds.
6. Press and hold 2 for 2 seconds to enter into the Date Setting Mode with double beep tone.

Date Setting Mode
1. Entering into the setting mode, year, month and day will then be displayed. Year will be flashing for setting. Month, day or day-month will be shown on upper row (same format as in Date Mode). Year will be shown on lower row.
2. Press 3 to advance the setting. If [3] is pressed and held for 2 seconds, auto advance function will be activated.
3. Press 1 to cycle through the settings for year, month and day.
4. If the setting is done, press 2 once to exit. Day of week will then be calculated automatically. Date Display Mode will then be retrieved.
5. If there is no operation for 60 seconds, the display will return to Date Mode.
6. Calendar and day of week can be calculated for the range of 01, Jan, 2000 to 31, Dec, 2099

Kaleido

Demo Mode
This watch ships in the demo mode, showing the display colors
alternating for two seconds each.
1. To take out of demo mode, press and hold the pusher for
two seconds.
2. To put back into demo mode, press and hold the pusher for two seconds.

Changing Colors
1. Make sure that it is out of demo mode.
2. Press the pusher to show color 1.
3. Press the pusher again to show color 2.
If you prefer to have the colors alternating, simply put the watch back into demo mode.

Time Setting
1. Pull crown out to position B.
2. Turn crown to set the desired time.
3. Return crown to position A.

Digital Chronograph

Analog Time Setting
Pull out the CROWN to it's position 1, and then turn the CROWN clockwise or counterclockwise to set the current time. Push the CROWN to it's Normal position 0 after current time is set.

Chrono mode operation
1. Press 1 to start the Chrono counting, the display will show the Chrono 1/100 Sec., Chrono Second, and Chrono Minutes by using 6 digits.
2. Press 2 to record Lap time. The 6 frozen digits on the display will be blinking for showing the Lap time. Press 2 again to release the display back into Chrono counting display. (Lap mode operation).
3. Press 1 to stop the Chrono counting. Then the display will show the final counting values.
4. Press 2 to reset the Chrono counter back to zero.

Display off mode operation
1. Press 1 and 2 at the same time for a moment, then the program will turn off the display and stop any counting.
2. Once entered into the display off mode, pressing any Button will exit the display off mode and take you back to the Normal display mode. The display will be reset and show the 6 digits in '00' values and all the animation patterns are cleared.